Exactly How to Install a Bath Tub Yourself
Go ServicesOn this page down the page you can discover a bunch of good information and facts in relation to How to Install a Bathtub Yourself.
Setting up a bath tub isn't exactly brain surgery, yet it does require solid plumbing, woodworking, and often, tiling abilities. Replacing an old bath tub with a new one is also a reasonably difficult task. If the old bathtub is readily easily accessible, the task can relocate easily; if you have to open a wall surface to get rid of the old tub as well as place the brand-new bathtub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will certainly require a helper to move out the old bathtub and also embeded in the new one. Ensure you have actually certified on your own for the job as well as are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed job, it is much better to take into consideration using one before you begin. Possibilities are you may require a specialist plumber to make tube links.
This write-up will help you install a new tub in your shower room if you have actually currently gotten a brand-new bathtub as well as don't need to alter the plan of your previous water system pipes.
Your tools as well as material checklist ought to make up the following:
Getting ready for the Installation
First of all, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two faucets making use of 2 nuts and also olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its final position.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you must do is disconnect the water supply. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The process of removing the existing faucets can be quite bothersome because of the limited gain access to that is frequently the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will originate from the pipes. When the supply pipes have actually been removed, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Mounting the Tub
Making use of the two wooden boards under its feet, position the bath tub in the required setting. The wood boards are handy in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The following goal is to make sure that the bathtub is leveled all round. This can be achieved by inspecting the level and changing the feet on the tub till the spirit level checks out degree.
To mount faucets, fit all-time low of the outermost flexible tap port to the ideal supply pipe by making a compression join; after that do the very same for the various other tap.
Switch on the water system as well as inspect all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill up the tub as well as additionally examine the overflow outlet and the normal outlet for leaks.
Lastly, deal with the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the tub must wait up until the tub has actually been made use of at the very least when as this will certainly resolve it right into its last placement.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end provides a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin ensuring that the washers remain in area in between the faucet as well as the sink. Protect the tap in place with the manufacturer provided backnut. As soon as the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with regular tap connectors. The former kind needs to be linked to the tap ends initially, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a stiff seal, causing the water to pass through the wall surface between the bathroom as well as the tiling, resulting in complications with wetness as well as possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bathtub with water prior to sealing, to permit the motion experienced when the bathtub remains in use. The sealer can crack rather early if you do not think about this motion before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly available on the marketplace. It is advisable to fit the floor tiles using water-resistant or water-proof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Give feedback further down. We will be pleased to know your responses about this blog entry. We are looking forward that you come back again before long. Remember to take the opportunity to promote this blog post if you enjoyed reading it. Many thanks for taking the time to read it.
Free Estimate